Cara Untuk Mengatasi Error E004-0101 Pada Mesin Canon Adance 6570
Salam jumpa lagi sobat fotocopy dimanapun anda semua berada, pada kesempatan kali ini saya akan mencoba untuk membagikan sedikit pengetahuan tentang Cara Mengatasi dari terjadinya Error E004-0101 pada mesin fotocopy Canon Adance 6570 yang mungkin anda semua belum mengetahui penyebab dan juga cara untuk mengatasinya.
Jika kita berbicara mengenai mesin fotocopy tentunya
sudah akrab dengan Error atau trouble shooting yang memang sering terjadi pada
mesin fotocopy, mungkin hal ini sudah tidak asing lagi bagi anda khususnya adan
memiliki usaha fotocopy komersil atau copy center yang memang setiap hari ber
urusan dengan mesin fotocopy, Biasanya anda lebih banyak mengalami dari keluarnya
Error yang mungkin masih agak asing buat kita yang berprofesi sebagi teknisi.
Error
code E004-0101, E004-0102, E004-0103
1.
Error
Code E000004-0101
The power supply on the IH is faulty or the IH
control mechanism is faulty.
After fixing the error, be sure to reset it on the
error.
(COPIER>FUNCTION>CLEAR>ERR)
Descriptions :
The power supply on the IH is faulty or the IH
control mechanism is faulty.
After fixing the error, be sure to reset the error.
(COPIER> FUNCTION> DELETE> ERR)
Description:
There is a mismatch between the input voltage and
the supply ID on the IH power.
Remedy:
-
Replace the power supply on the
repairing heater with one that has been designed for the country of
installation (voltage).
-
Check the connector again for any errors
in the connection.
-
Replace the power supply on the heater
for repair.
-
Replace the DC controller PCB unit
E004-0101: Halogen heater is damaged or terminal of
heater has poor contact.
Because of damage to the halogen heater (H1) or poor
contact of a heater terminal, the error code "E004-0101" was
indicated. This error code may be indicated due to a fault in the AC Driver PCB
(i.e., triac short), the fixing assembly, and the DC Controller PCB 2 (MAISY).
However, before replacing these parts, perform the following procedure.
- E004-0101 can be displayed when there is a
short-circuit detection error in the halogen heater (ASIC detection).
1. Detach
the terminal on both ends of the halogen heater, and then check to see if the
heater has electrical continuity; if there is no electrical continuity, replace
the heater with a new one.
2. Check
to see if the terminal [A] on both ends of the heater is fixed firmly with a
screw. If the screw is loosened, tighten it.
3. If
the symptom still occurs, check to see if J114 connector of the AC Driver PCB
is disconnected. If disconnected, re-fit it.
FK2-2532-000 Halogen Heater (120V)
FM3-0266-000 DC Controller PCB 2 (MAISY)
FM2-6301-000 AC Driver PCB
2.
Error
Code E000004-0102
There is an abnormal rise in temperature. After you
fix the error, be sure to reset it to the error that occurred.
(COPIER>FUNCTION>CLEAR>ERR)
Descriptions
:
The IH current is faulty. (current leakage)
Remedy :
-
Replace the power supply on the heater
for repair with one designed to match the country of installation (voltage).
-
Check the connector again for errors in
the connection.
-
Replace the power supply on the heater
for repair.
-
Replace the DC controller PCB unit
3.
Error
Code E000004-0103
There is an abnormal rise in temperature. After you
fix the error, be sure to reset it to the error that occurred.
(COPIER>FUNCTION>CLEAR>ERR)
Descriptions
:
The IH current is faulty. (no current)
Remedy :
-
Replace the power supply on the heater
for repair with one designed for the country of installation (voltage).
-
Check the connector again for any errors
in the connection.
-
Replace the fixing heater power supply.
-
Replace the DC controller PCB
Jangan lupa untuk mengikuti blog ini agar selalu
dapat update terbaru yang mungkin dapat bermaanfaat buat anda yang mesin
fotocopy sedang mengalami masalah Error yang mungkin belum anda ketahui
penyebab serta cara untuk mengatasinya selebihnya saya ucapkan banyak-banyak
terimakasih
Posting Komentar untuk "Cara Untuk Mengatasi Error E004-0101 Pada Mesin Canon Adance 6570"