Cara Mengatasi Error Code E027-0001 Canon iR Advance 6075
Salam
jumpa lagi pada kesempatan kali ini saya akan mencoba untuk berbagi sedikit
pengalam tentang cara mengatasi Permasalahan dari keluarnya Error
Display E027-001 yang terjadi pada mesin fotocopy
Canon IRA6055/6065/6075 ini merupakan masalah yang
kerap terjadi, bukan hanya pada mesin type lawas, seri terbaru mesin fotocopy
iR advance pun tentu ada problem Error.
Seperti yang sudah kita ketahui bersama
bahwa kondisi Error yang keluar pada mesin adalah memberikan peringatan bahwa
sada kerusakan yang terjadi pada mesin dan kode Error ini juga akan menyebabkan
mesin untuk berheti bekerja dan tidak dapat lagi untuk melakukan pekerjaan sama sekali seperti biasanya karena akibat
dari Error ini.
Keterangan :
Toner Supply Motor error
Lock error of the Toner Supply Motor (M10)
Perbaikan yang bisa anda lakukan :
·
Periksa koneksi Connector. Pada Sisi
samping posisi motor: J2037, Rel pada sisi depan: J3080, dan juga Sisi samping
bagian belakang: J3063, sisi pada Sirkuit Penggerak Utama PCB (PCB2): J117
·
Lepaskan pada bagian Penampung Toner,
dan juga lakukan pemeriksaan apakah terjadi kesalahan. Jika kesalahan tidak
terjadi kemudian pasang kembali wadah toner dan lakukan pemeriksaan lagi. Jika
terjadi kesalahan, periksa area penggerak titik sambungan wadah. Jika terjadi
kesalahan.
·
Ganti Toner Supply Motor (M10).
·
Ganti PCB Driver Utama (PCB2).
·
Ganti DC Controller PCB (PCB1).
KODE: E032-0001
·
Keterangan :Kegagalan NE Controller
Counter
·
Detection of open circuit pulse signal
counts
Perbaikan :
Disconnection of cable
KODE: E041-0001
·
Keterangan : Deck Right Decker Motor
error
·
Overcurrent of the Right Deck Lifter
Motor terdeteksi.
Perbaikan :
·
Periksa perpindahan Wire Lifter dari
Right Deck.
·
Periksa penghalang yang berfungsi untuk menghaluskan
gerakan Deck Base Plate dari Right Deck.
CODE: E053-0001
·
Keterangan : Error in Reverse Upper
Flapper Detection of solenoid connections
·
The Reverse Connection on the Upper
Solenoid Flapper (SL5) cannot be detected 5 times with a time interval of less
than 20 msec.
·
Perbaikan : 1. Check the Reverse connection on the
Upper Solenoid Flapper (SL5). Side of the solenoid: J2115, and the PCB side of
the Duplex Driver unit: J340 2. Replace the Reverse Upper Flapper Solenoid
(SL5). 3. Replace the Duplex Driver PCB (PCB4). 4. Replace the DC Controller
PCB (PCB1).
CODE: E060-0001
·
Keterangan : Primary Charging Shutter
Error occurs when HP is open
·
The sensor on the Primary Charging
Shutter (PS94) detects that the shutter remains open even if it is moved to the
closest position.
Perbaikan :
·
Check the Shutter position on the
Primary Charging and Cleaning Pad.
·
In case the Primary Charging Shutter and
Cleaning Pad fail to operate (stop at HP on the front side)
·
Re-check the Cleaning Motor connection
on the Main Charging Wire (M6). Motor side: J3017, J3060 (iR-ADV 8xxx) or J3160
(iRADV 6xxx) (relay), PCB side: J3177 (relay), J107 and (Main Driver PCB
(PCB2))Replace the Primary Charging Wire Cleaning Motor (M6).
·
In the case of Primary Charging Shutter
and also the Cleaning Pad is stopped in the rear position (close operating
position)
·
Check the Sensor connection on the
Primary Charging Shutter (PS94). On the sensor side: J2029, J3089 (relay), PCB
side: J3088 (relay), J114 (Main Driver PCB (PCB2))
·
Change the Sensor in the Main Charging
Shutter section (PS94).
·
In the case of a Primary Charging
Shutter and also the Cleaning Pad is stopped along the way
·
Check the position of the screw
clearance on the Slider Pin and the abrasion pin. Tighten the screw or replace
the Pin Slider.Replace the Primary Charging Assembly.
·
In the case of Primary Shutter the
Primary Charging section stops at the front side and the Cleaning Pad moves to
the rear side
·
Check whether the Shutter Mounting Plate
section is damaged. If so, replace the Shutter Unit.
·
Check for looseness that occurs in the
screws on the Slider Pin and abrasion pins. Tighten the screws or replace the
Pin Slider.
·
Replace the Primary Filling Unit part.
·
Replace the Main Driver PCB (PCB2). 3.
Replace the DC Controller PCB unit (PCB1).
CODE: E000-0001
Description:
Memperbaiki kesalahan suhu rendah Rakitan
Suhu Thermistor Utama Fixing (THM1) tidak mencapai
70 derajat Celcius meskipun 20 detik telah berlalu setelah memulai kontrol suhu
Fixing Roller.
Perbaikan :
- Periksa koneksi dari Fixing Assembly. (Kesalahan koneksi Laci, pemutusan konektor, sirkuit terbuka) -> Ganti Unit Pemanas.
- Periksa koneksi antara Main Driver PCB (PCB2) dan Fixing Power Supply PCB (PCB10) (pemutusan konektor, sirkuit terbuka, kabel yang tertangkap).
- Pasang kembali Memperbaiki Catu Daya PCB (PCB10).
- Pasang kembali PCB Driver Utama (PCB2).
- Pasang kembali DC Controller PCB (PCB1).
CODE: E001-0004
Description:
·
Fixing Assembly high temperature error
(hardware detection)
·
An abnormal temperature difference
between the Thermistors has been detected.
Remedy :
1. Check
whether the cable in the Thermistor is stuck or open. -> Change the
Thermistors part. -> Replace on the Repairing Top Uni
2. Replace
the Main Driver PCB (PCB2).
3. Replace
the DC Controller PCB (PCB1).
4. Check
if the Fixing Shutter operates. -> Replace the Fixing Assembly.
Itulah sedikit tips dan juga cara untuk mengatasi
dari problem terjadinya Permasalahan dari keluarnya Error
Display E027-001 yang terjadi pada mesin fotocopy
Canon IRA6055/6065/6075 semoga dengan adanya artikel ini dapat membantu masalah
yang terjadi pada mesin fotocopy milik anda, sekian dan terimakasih.
We prefer your present post. It may be excellent to see anybody clarify within phrases with the cardio together with lucidity with this crucial concern may be rapidly observed. copier service near me
BalasHapus